biasing current中文是什么意思

• 偏磁电流
• 偏压电流

• "bias"中文翻译    vt. (biased, biasing 〔英国〕 bi ...
• "current"中文翻译    adj. 1.通用的，流行的。 2.现在的，现时的，当时 ...
• "alternating current biasing" 中文翻译 :    交流偏磁
• "alternating current biasing method" 中文翻译 :    交流偏压法
• "alternating current magnetic biasing" 中文翻译 :    交流偏磁
• "alternating-current magnetic biasing" 中文翻译 :    交流磁偏压
• "assistating current magnetic biasing" 中文翻译 :    交莲磁
• "direct current biasing" 中文翻译 :    直莲压法; 直流偏压法; 直流偏置
• "biasing" 中文翻译 :    附加励磁; 加偏磁 加偏压; 偏压
• "alternative biasing" 中文翻译 :    交替偏压
• "auto biasing" 中文翻译 :    自动偏磁
• "biasing battery" 中文翻译 :    偏压电池, 偏 流电池
• "biasing capacitance" 中文翻译 :    偏压电容
• "biasing characteristic" 中文翻译 :    控制特性; 偏置特性
• "biasing circuit" 中文翻译 :    (电子管)偏压电路; 偏流电路; 偏置电路
• "biasing field" 中文翻译 :    偏压场
• "biasing holography" 中文翻译 :    偏置全息照相术
• "biasing impedance" 中文翻译 :    偏压阻抗; 偏置阻抗
• "biasing logic" 中文翻译 :    偏置逻辑
• "biasing resistance" 中文翻译 :    偏压电阻, 偏流电阻
• "biasing resistor" 中文翻译 :    偏压电阻; 偏置电阻
• "biasing spring" 中文翻译 :    偏动弹簧; 偏动簧片
• "biasing sputtering" 中文翻译 :    偏压溅射
• "biasing technique" 中文翻译 :    偏置技术
• "biasing transformator" 中文翻译 :    偏压变压器

• Input bias current
  输入偏压电流
• On top of that is the user " brightness " adjustment , which adjusts the bias currents to all tubes at the same time
  此后就是用户使用的“亮度”调整了，此项同时对三只管子的偏置电流进行调整。
• Again , consider using amplifiers that exhibit a smooth input bias current transition throughout the applied input common - mode voltage
  再者，所用的放大器也要考虑在加到输入端的整个共模电压(范围内)输入偏置电流转换保持平滑。
• The g2 adjustment is a service or factory level adjustment , normally only done at the factory or at installation , which adjusts the bias current for each tube individually so that they all come on at the same time
  每一只投影管都需要一定量的偏置电流才能够正常工作，然而，每只管及其相应的电路参数都会有些差异，因此所需的偏置电流也不太一样。
• The results of numerical simulation show that for various kinds of noise without modulation the anti - noise properties and the output quality of laser can be improved by selecting appropriately bias current and parameters of the cavity
  数值模拟的结果表明，对于无调制时的各种噪声，适当选取偏置电流和腔内参数可以提高微腔半导体激光器的抗噪声性能或激光输出的质量。
• To reduce power dissipation of the amplifier , a kind of on / off technology is used in the circuit . with a little bias current circuit to control the main bipolar transistor operation , the transistor will be in a state of on / off
  采用器件旁路小电流工作电路,实现对低噪声放大器主要工作晶体管的控制,使该晶体管按需要分别处于工作或关断状态,保证了放大器的极低功耗。
• Second , since input bias currents are not always small and can exhibit different polarities , source impedance levels should be carefully matched to minimize additional input bias current - induced offset voltages and increased distortion
  其次,因为输入偏置电流不一定都小,且可能体现不同的极性，而且源阻抗水平应该仔细地进行匹配，以将输入偏置电流引起额外失调电压和增加的畸变减到最小。
• And a novel systematically method , using linear combination approach to design high order filter , has been proposed . the designed filters can be adapted by adjusting the bias currents , without changing the physical structure . the results of the examples and pspice simulator show the advantages and availabilities of this method
  并且提出了多项式线性组合法,采用该方法不但能设计出所要求的高阶电流滤波器,而且能在不改变物理结构的情况下,利用电流控制传送器的特性,调整其偏置电流,实现滤波器输出特性的改变。
• The results that increasing of bias current and shunted resistance and lowing critical current and connected inductance can decrease the transmission time are shown ; ( 4 ) a new type of circuit , ladder shape multiplayer jtl . structure is provided by author , thus output signal of rsfq circuits can be amplified before transfer to room temperature electronics system . it has highly gain of amplify relatively and the double peak structure are avoided through decreasing parasitic capacitance
  ( 4 )针对目前超导与室温接口电路的电压放大器存在的“双峰”和放大增益效率较低的不足，提出了一种全新的阶梯式多层jtl电压放大电路结构，较好的解决了以上的问题，通过初步的仿真分析证实，该电路的构思极负有创新性。
• The bias magnetic field of the bias coil driven by bias current and small signal test current , results in the induced signal of the control coil . the terminal voltage of the control coil is detected by the test circuit . then the signal containing the information of rotor displacement is obtained , from which we can get the dc voltage signal proportional to the rotor displacement through half - wave rectification circuit and low pass circuit . this dc signal is put into a pid controller to get the control signal of the rotor displacement
  偏置测试电路向偏置线圈输入偏置电流和小信号测试电流,两者产生的偏置磁场在控制线圈产生感应信号,检测电路检测控制线圈端电压并提取含有转子位移信息的电压信号,该信号经半波整流电路和低通滤波电路后得到与转子位移成正比例的直流信号,再由pid控制器转换为转子位移的控制信号,最后控制信号输入功放电路产生控制电流,实现闭环控制。

• biasing current перевод